Reset your Holosun EPS Carry Red Dot Sight

Wiki Article

Occasionally, you may require to reinitialize your Holosun EPS Carry Red Dot sight to its factory settings. This can be helpful if you've been tinkering with the adjustments or are experiencing unexpected behavior. Fortunately, resetting your Holosun is a straightforward process that can be performed in just a few steps.

• Initially ensuring your red dot sight is turned on.
• Locate the small button for reset on the side of the sight.
• Employ a thin tool to press and hold the reset button for approximately three seconds.
• Release the reset button and your Holosun EPS Carry Red Dot sight will restart.
• Your red dot sight should now be set back to its factory settings.

Restore Your Holosun EPS Carry Red Dot to Defaults

In case you've tweaked your Holosun EPS Carry red dot settings and want to return to original, resetting it to default configuration is a breeze. First, find the tiny button on the bottom of your optic. Then, press and hold it for around twelve seconds until you see the red dot blink. Your Holosun EPS Carry is now reset to its factory settings, ready for accurate shooting.

Bring Your Holosun EPS Carry Back to Action

Is your beloved Holosun EPS Carry experiencing some performance problems? Don't despair! A simple factory reset can often solve the problem and get your red dot sight back to its former glory. Before you begin, remember to detach the battery from your Holosun EPS Carry to prevent unintended activation during the process.

To perform a factory reset on your Holosun EPS Carry, follow these straightforward steps:

• Simultaneously press and hold the power button for approximately 5 seconds.
• An indicator will flash, indicating that the reset is in progress.
• Stop pressing the power button once the reset is complete.

Your Holosun EPS Carry should now be back to its factory settings. You can connect the battery and verify your sight's functionality. If you encounter any further troubles, don't hesitate to contactsupport team.

Return Factory Settings on Your Holosun EPS Carry: A Step-by-Step Guide

Resetting your Holosun EPS Carry to factory settings can be a helpful solution if you're experiencing issues with the optic or simply want to start fresh. This process erases all user configurations and returns the sight to its original state. Before proceeding, remember to note down any customizations you have made as they will be lost during this process. Follow these steps carefully to ensure a successful factory reset.

• Beginning with, Energize your Holosun EPS Carry by pressing the power button.
• Next, press and hold both the mode button and the up/down adjustment button simultaneously.
• During continue holding these buttons, press the power button once.
• You will show a confirmation prompt indicating that the reset process is initiated.
• Enable the process to complete. This may take a few moments. Once done, your Holosun EPS Carry will automatically power off.

After resetting your Holosun EPS Carry to factory settings, you will need to re-enter any desired customizations, such as brightness levels how to factory reset Holosun EPS Carry red dot and reticule style. Refer to the user manual for detailed instructions on configuring your optic after a reset.

Erase All Settings on Your Holosun EPS Carry

To Factory reset your Holosun EPS Carry sight, you'll need to access the settings menu. This can usually be done by Pressing a specific button combination. Consult your Manual for the exact button sequence for your model. Once in the settings menu, look for an option that says "Clear Settings". Select this option and confirm the reset. Your sight will then power off and restart with all settings Restored to their default values.

Reset your Holosun EPS Carry through a Factory Default Settings

If your Holosun EPS Carry is acting funny, a factory reset might be the fix. This will return your sight to its original settings, clearing any altered configurations you've made. To execute this reset, adhere to these straightforward steps:

• To begin, locate the reset button on your EPS Carry.
• Secondly, press a thin object, like a paperclip, to depress the reset button.
• As you maintain the reset switch pressed, turn your EPS Carry.
• It will blink a message showing that the reset is complete.

Once the reset is complete, your EPS Carry will be set to its factory settings.

Report this wiki page